4140 ht hardness Related introduction

  1. Technical Information: 4140 HT - SB Specialty Metals

    4140 HT Surface Hardening . 4140 HT is a medium carbon alloy steel heat treated to a . nominal hardness of 28-32 HRC. 4140 HT can also be surface hardened to increase wear resistance . Typical Chemical Composition

  2. Wingate Alloys Inc.

  3. 4140 HIGH TENSILE STEEL - interlloy.com.au

    4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting 4140 ht hardness

  4. 4140 High Tensile Steel, Interlloy, Engineering Steels ...

    4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting mechanical properties.

  5. AISI 4140 Alloy Steel (UNS G41400) - azom.com

    AISI 4140 alloy steel is a chromium-, molybdenum-, and manganese-containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. The following datasheet gives an overview of AISI 4140 alloy steel.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  6. 4140 Alloy Steel Data Sheet - Eastern Tool Steel Service, Inc.

  7. 4140HW Alloy Steel Technical Data

    Figure 9 (Mechanical Properties for 4140 and 4140HW) The data represents a mechanical property comparison of several 4140 and 4140HW heats. Figure 10 (Jominy Hardenability Curve for 4140 and 4140HW) The data represents an average of Jominy results from several 4140 and 4140HW heats. For more information, visit www.timkensteel.com or call us

  8. 4140 Heat Treated Steel Plate, Precision Grinding, Inc.

  9. 4140 Pre Hard - BICO Steel Service Centers

    616.453.2400 / 800.962.4140 F: 616.453.2929 www.bicomichigan.com [email protected] BICO SOUTH, INC. Spartanburg, SC 864.574.2121 / 800.998.1025 F: 864.574.4140 www.bicosouth.com [email protected] 4140 Pre Hard 4140PH is a chromium-manganese-molybdenum grade This grade is delivered in a prehardened condition at a hardness level of 4140 ht hardness

  10. HIGH TENSILE STEEL AISI 4140 -

    HIGH TENSILE STEEL AISI 4140 AISI 4140 Chrome - Moly High Tensile Steel, generally supplied hardened and tempered to Condition T in sections up to 100mm, with a tensile strength of 850 1000 MPa and aiming for this strength range in larger sections. It offers a very good balance of strength, toughness and wear-resistance.

  11. 4140 Steel, 4150 Steel, B7, Associated Steel Corporation

    MIRRALOY® TGP [4140/4150 (modified) Turned Ground & Polished, High Strength Alloy Shaft] It is offered in the heat treated, TGP condition. Typical hardness is Rockwell C 28/34. Typical tensile strength 156,000 PSI. This is a near bearing-fit shaft.

  12. AISI 4140 Chrome-Molybdenum High Tensile Steel

    AISI 4140 is a chromium-molybdenum alloy steel. The chromium content provides good hardness penetration, and the molybdenum content ensures uniform hardness and high strength. AISI 4140 chrome-molybdenum steel can be oil hardened to a relatively high level of hardness

  13. Wingate Alloys Inc.

    AISI 4140. 4140 Chromium-Molybdenum Steel is supplied in the annealed or prehardened condition. 4140 HT prehardened condition which is heat treated to a medium hardness (HRC 28/32). 4140 HT is supplied in many forms such as; hot rolled or turned, ground and polished rounds and DCF plate which is used as a holder material for high strength structural components.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  14. Wingate Alloys Inc.

  15. 4140 Pre Hard - BICO Steel Service Centers

    616.453.2400 / 800.962.4140 F: 616.453.2929 www.bicomichigan.com [email protected] BICO SOUTH, INC. Spartanburg, SC 864.574.2121 / 800.998.1025 F: 864.574.4140 www.bicosouth.com [email protected] 4140 Pre Hard 4140PH is a chromium-manganese-molybdenum grade This grade is delivered in a prehardened condition at a hardness level of 4140 ht hardness

  16. Speedy Metals Information for 4142 HT TGP Shafting

    4142 HT Turned, Ground and Polished is a chromium-molybdenun alloy steel that has been hardened to 27 to 32 Rockwell C and is ready to use while still machinable and of exceedingly high strength. The chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength.

  17. AISI 4140 Steel, oil quenched, 540°C (1000°F) temper, 25 ...

    Property Data; This page displays only the text of a material data sheet. To see MatWeb's complete data sheet for this material (including material property data, metal compositions, material suppliers, etc), please click the button below.

  18. 4140-HT, Lindquist Steels

    Home / Products / 4140-HT 4140-HT is a high alloy tool steel that has good strength, toughness, and mechanical properties. 4140-HT comes supplied pre-hardened at 26-32 HRC and is available in Plate, Block, and Round bar forms.

  19. Machinable, heat treated 4140 - The Home Machinist!

    Dec 25, 2009 · are all "heat treatments". So a name like "4140 heat treat" leaves me a bit doubtful about what I am getting for my money. So my questions are, a. What is the proper designation for the machinable version of heat treated 4140 ? b. What are its mechanical properties (e.g. yield strength, hardness etc.)? c.

  20. MetalsDepot® - 4140 Alloy Steel Flat Bar

    4140 Alloy Steel Flat is an cold drawn annealed steel of relatively high hardenability with its chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. 4140 Alloy Steel Flat responds well to heat-treatment and is relatively easy to machine in the annealed condition.

  21. 4140 Q&T TG&P - myalro.com

    4140 Q&T is a steel in the family of SAE steel grades, as specified by the Society of Automotive Engineers (SAE). Alloying elements include chromium and molybdenum, and as a result these materials are often informally referred to as chromoly steel (common variant stylings include chrome-moly, CrMo, CRMO, CR-MOLY, and similar).Some results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation